Welcome to the Irish Mini Owners Club Forum. Keep an eye out of on coming events!!!!

1981 Mini City 1000

This section is for Mini projects and restorations and also the place to show off your pride and joy.

Moderators: irishminis, spud1979, The Marcos Graveyard, Moderators

ctwomey
NON Member
Posts: 127
Joined: Thu Jan 03, 2019 9:44 am
Whats your location?: Ballybrittas, Co. Laois
Region: Eastern
What Minis have you?: I owned a 1978 Mini 850 when I was in my late teens. I owned a 1986 Mini Chelsea that I imported from the UK. Also owned a 1982 MG Metro that was bored out to 1293. Restoring a 1981 Dublin Mini City.
Contact:

Re: 1981 Mini City 1000

Post by ctwomey » Tue Jul 06, 2021 3:20 pm

I cut out all the rotten floor in the driver's rear corner
IMG_5020.jpeg
Made up a carboard template of the patch panel
IMG_5019.jpeg
Cut a patch panel out using the old outer skin of the door
IMG_5021.jpeg
All Cleco'd up now with just the plug weld holes to create. Should weld it all up this weekend.
9B42A6A3-26C3-4E38-8E2A-A53C914B7FFB.JPG
This is the finished strip in the background of the previous image
IMG_5018.jpeg



colinf1
NON Member
Posts: 144
Joined: Mon Aug 24, 2020 10:27 am
Whats your location?: Dundalk
Region: Eastern
What Minis have you?: 1974 Aussie Leyland Mini 998 (Clubman front)
Current project is a 1983 Mini 1000
Contact:

Re: 1981 Mini City 1000

Post by colinf1 » Wed Jul 07, 2021 10:34 am

Would you recommend the Cleco clips or could you get away with plenty of vice grips?

ctwomey
NON Member
Posts: 127
Joined: Thu Jan 03, 2019 9:44 am
Whats your location?: Ballybrittas, Co. Laois
Region: Eastern
What Minis have you?: I owned a 1978 Mini 850 when I was in my late teens. I owned a 1986 Mini Chelsea that I imported from the UK. Also owned a 1982 MG Metro that was bored out to 1293. Restoring a 1981 Dublin Mini City.
Contact:

Re: 1981 Mini City 1000

Post by ctwomey » Wed Jul 07, 2021 8:10 pm

colinf1 wrote:
Wed Jul 07, 2021 10:34 am
Would you recommend the Cleco clips or could you get away with plenty of vice grips?
Great for pinning panels where you can't get a clamp to the back of them. However, the best is that you can align two panels together, drill the 3.5mm Cleco holes and every time you take the panel off for tweaking, painting etc. you can ensure it goes back into the exact same place afterwards.

Mind you Lidl do a 3 x pack of small vice-grips for €7.99 that are great for holding panels together too.

colinf1
NON Member
Posts: 144
Joined: Mon Aug 24, 2020 10:27 am
Whats your location?: Dundalk
Region: Eastern
What Minis have you?: 1974 Aussie Leyland Mini 998 (Clubman front)
Current project is a 1983 Mini 1000
Contact:

Re: 1981 Mini City 1000

Post by colinf1 » Sat Oct 02, 2021 8:18 am

Any updates on how the restoration is going?

ctwomey
NON Member
Posts: 127
Joined: Thu Jan 03, 2019 9:44 am
Whats your location?: Ballybrittas, Co. Laois
Region: Eastern
What Minis have you?: I owned a 1978 Mini 850 when I was in my late teens. I owned a 1986 Mini Chelsea that I imported from the UK. Also owned a 1982 MG Metro that was bored out to 1293. Restoring a 1981 Dublin Mini City.
Contact:

Re: 1981 Mini City 1000

Post by ctwomey » Mon Oct 04, 2021 9:32 am

colinf1 wrote:
Sat Oct 02, 2021 8:18 am
Any updates on how the restoration is going?
Hi Colin, I can't believe my last post was in July :(

I had the greatest of intentions to work on it all through the Summer but alas, other things got in the way. I have been tipping away doing small bits but I need to start block booking time out in the garage again. I didn't really want to spend the Summer evenings out in the garage, weather was too good not to be outside. Now that the Autumn/Winter is upon us time to get stuck into it again.

ctwomey
NON Member
Posts: 127
Joined: Thu Jan 03, 2019 9:44 am
Whats your location?: Ballybrittas, Co. Laois
Region: Eastern
What Minis have you?: I owned a 1978 Mini 850 when I was in my late teens. I owned a 1986 Mini Chelsea that I imported from the UK. Also owned a 1982 MG Metro that was bored out to 1293. Restoring a 1981 Dublin Mini City.
Contact:

Re: 1981 Mini City 1000

Post by ctwomey » Mon Dec 13, 2021 11:18 am

Easing myself back into the welding again over the last couple of weeks.

Finally, have the welder 'tuned in' and have it nice and hot without it blowing through. I think I was trying to get it too cold and that was making life a little difficult.
IMG_7377.jpeg
Rust is hidden in lots of places that needs to be cut out.
IMG_7416.jpeg
IMG_7422.jpeg
IMG_7424.jpeg
IMG_7425.jpeg
Hard to see where I made the welds.

colinf1
NON Member
Posts: 144
Joined: Mon Aug 24, 2020 10:27 am
Whats your location?: Dundalk
Region: Eastern
What Minis have you?: 1974 Aussie Leyland Mini 998 (Clubman front)
Current project is a 1983 Mini 1000
Contact:

Re: 1981 Mini City 1000

Post by colinf1 » Mon Dec 13, 2021 4:45 pm

Thats pretty good blending!

ctwomey
NON Member
Posts: 127
Joined: Thu Jan 03, 2019 9:44 am
Whats your location?: Ballybrittas, Co. Laois
Region: Eastern
What Minis have you?: I owned a 1978 Mini 850 when I was in my late teens. I owned a 1986 Mini Chelsea that I imported from the UK. Also owned a 1982 MG Metro that was bored out to 1293. Restoring a 1981 Dublin Mini City.
Contact:

Re: 1981 Mini City 1000

Post by ctwomey » Mon Dec 20, 2021 8:59 pm

Old door skins are great for patch panels

Where does everyone else get their 20 gauge/0.9mm sheets?
Haven’t had much luck locally here in Laois.
D16EA1F6-2E13-4551-A61F-977E90600815.jpeg

ctwomey
NON Member
Posts: 127
Joined: Thu Jan 03, 2019 9:44 am
Whats your location?: Ballybrittas, Co. Laois
Region: Eastern
What Minis have you?: I owned a 1978 Mini 850 when I was in my late teens. I owned a 1986 Mini Chelsea that I imported from the UK. Also owned a 1982 MG Metro that was bored out to 1293. Restoring a 1981 Dublin Mini City.
Contact:

Re: 1981 Mini City 1000

Post by ctwomey » Wed Dec 22, 2021 6:27 pm

Drilled a few 6mm holes to plug weld from the other side when the patch is welded in.
IMG_7445.jpeg
Patch panel clamped in place
IMG_7446.jpeg
Tacked the patch in place and trimmed it back
IMG_7450.jpeg
Completed the weld. I used a stainless steel plate pushed between the boot and boot floor lip to take out the heat.
IMG_7451.jpeg
Weld ground down and some sprayed with some weld through primer.
Attachments
IMG_7453.jpeg

ctwomey
NON Member
Posts: 127
Joined: Thu Jan 03, 2019 9:44 am
Whats your location?: Ballybrittas, Co. Laois
Region: Eastern
What Minis have you?: I owned a 1978 Mini 850 when I was in my late teens. I owned a 1986 Mini Chelsea that I imported from the UK. Also owned a 1982 MG Metro that was bored out to 1293. Restoring a 1981 Dublin Mini City.
Contact:

Re: 1981 Mini City 1000

Post by ctwomey » Mon Dec 27, 2021 8:24 pm

Cleaned up the boot floor butt weld. One small pin hole to fix but happy with the results. New valence closing panels arriving in a couple of days. Will start the other side soon and then will be close to finishing the rear end repairs.
90C6B0EF-8E0D-4EF1-A2B5-096F2241DE9C.jpeg

colinf1
NON Member
Posts: 144
Joined: Mon Aug 24, 2020 10:27 am
Whats your location?: Dundalk
Region: Eastern
What Minis have you?: 1974 Aussie Leyland Mini 998 (Clubman front)
Current project is a 1983 Mini 1000
Contact:

Re: 1981 Mini City 1000

Post by colinf1 » Tue Dec 28, 2021 9:32 am

Looking nice and tidy!

Have you set a finish date?

ctwomey
NON Member
Posts: 127
Joined: Thu Jan 03, 2019 9:44 am
Whats your location?: Ballybrittas, Co. Laois
Region: Eastern
What Minis have you?: I owned a 1978 Mini 850 when I was in my late teens. I owned a 1986 Mini Chelsea that I imported from the UK. Also owned a 1982 MG Metro that was bored out to 1293. Restoring a 1981 Dublin Mini City.
Contact:

Re: 1981 Mini City 1000

Post by ctwomey » Tue Dec 28, 2021 12:01 pm

colinf1 wrote:
Tue Dec 28, 2021 9:32 am
Have you set a finish date?
I thought I would get most of the body work done this year with it on the road by Summer ‘22 but I am way behind schedule. Family and work commitments have taken a priority in ‘21. As long as I keep tipping away it will get done. I am enjoying the whole process.

There is the fear too of screwing it up, so slow and steady until I become really proficient at the welding. It’s not cheap restoring any car and the country is littered with half finished and abandoned projects. Don’t want to be in that category.

ctwomey
NON Member
Posts: 127
Joined: Thu Jan 03, 2019 9:44 am
Whats your location?: Ballybrittas, Co. Laois
Region: Eastern
What Minis have you?: I owned a 1978 Mini 850 when I was in my late teens. I owned a 1986 Mini Chelsea that I imported from the UK. Also owned a 1982 MG Metro that was bored out to 1293. Restoring a 1981 Dublin Mini City.
Contact:

Re: 1981 Mini City 1000

Post by ctwomey » Mon Jan 03, 2022 8:26 pm

Finally started repairing the passenger side boot floor
31B41F6F-BA01-46F6-968C-4132BE39DB9A.jpeg
Requires a similar patch panel to the driver’s side. Managed to salvage the fuel tank bracket too.

colinf1
NON Member
Posts: 144
Joined: Mon Aug 24, 2020 10:27 am
Whats your location?: Dundalk
Region: Eastern
What Minis have you?: 1974 Aussie Leyland Mini 998 (Clubman front)
Current project is a 1983 Mini 1000
Contact:

Re: 1981 Mini City 1000

Post by colinf1 » Mon Jan 03, 2022 9:18 pm

Are there any other patches required on the boot floor?

Looks like your chipping away at making good progress!

ctwomey
NON Member
Posts: 127
Joined: Thu Jan 03, 2019 9:44 am
Whats your location?: Ballybrittas, Co. Laois
Region: Eastern
What Minis have you?: I owned a 1978 Mini 850 when I was in my late teens. I owned a 1986 Mini Chelsea that I imported from the UK. Also owned a 1982 MG Metro that was bored out to 1293. Restoring a 1981 Dublin Mini City.
Contact:

Re: 1981 Mini City 1000

Post by ctwomey » Mon Jan 03, 2022 9:46 pm

colinf1 wrote:
Mon Jan 03, 2022 9:18 pm
Are there any other patches required on the boot floor?
Only small repairs
IMG_7595.jpeg
IMG_7596.jpeg
IMG_7597.jpeg
and then onto the two quarter panel window openings

Driver's side is not too bad, just a small section
IMG_7599.jpeg
Passenger one will require more work. Might need to finally invest or create a steel folding machine.
IMG_7598.jpeg

ctwomey
NON Member
Posts: 127
Joined: Thu Jan 03, 2019 9:44 am
Whats your location?: Ballybrittas, Co. Laois
Region: Eastern
What Minis have you?: I owned a 1978 Mini 850 when I was in my late teens. I owned a 1986 Mini Chelsea that I imported from the UK. Also owned a 1982 MG Metro that was bored out to 1293. Restoring a 1981 Dublin Mini City.
Contact:

Re: 1981 Mini City 1000

Post by ctwomey » Thu Jan 06, 2022 8:57 pm

Got the other boot floor patch panel tacked in this evening.
B0A1BF5B-DA5C-4E17-B152-D99A5EE54C88.jpeg
From the other side
6F4C5EE8-CF4E-464A-A439-4BC16E77613A.jpeg

Post Reply

Who is online

Users browsing this forum: No registered users and 1 guest