Welcome to the Irish Mini Owners Club Forum. Keep an eye out of on coming events!!!!

Help Needed!!

General MINI related posts. Open to all, registration required

Moderators: spud1979, The Marcos Graveyard, Moderators

Post Reply
mini mad sam
NON Member
Posts: 84
Joined: Sun Feb 06, 2011 10:29 pm
Whats your location?: midleton, county cork.
Region: Southern
What Minis have you?: 1985 MINI
1991 MINI
1975 MINI CLUBMAN ESTATE
Contact:

Help Needed!!

Post by mini mad sam »

Hi when I'm driving my mini if i brake, slow down or change gear there is a loud bang and a judder from the left side wheel (i think).
I checked engine mountings, they are good.
Any idea what could be wrong??

Thanks.


User avatar
purplehaze
NON Member
Posts: 990
Joined: Wed Mar 30, 2011 2:42 pm
Whats your location?: Tallaght :p
Region: Southern
What Minis have you?: 1980 clubman b16 vtec
1992 mini shell, getting turbo,d
1974 clubman estate
Modifications: original-ish pffffft ye rite
Contact:

Re: Help Needed!!

Post by purplehaze »

Could be any thing. I had same prob from mine. My ball joints were Nackered...could be wheel bearings or drop links. Jack the car up an wiggle the wheel hand on top of wheel and other hand on bottom. Pull an push on it. If it wobbles its either wheel bearing drop links or ball joints. Hope this helps
If it's bigger than a mini it's not a mini
minionly
NON Member
Posts: 720
Joined: Sat May 16, 2009 9:08 pm
Whats your location?: tallaght dublin 24
Region: Southern
What Minis have you?: leyland mini clubman 76 saloon
Modifications: painted in granit graey. 1293 engine block bored out too 1312. sw5 cam .1.5 high lift rolling rockers. electrionic fuel pump .webber 45 carb. millennium rc40 exhuast system center exit. copper 10inch brake set up .and dunlop d1s alloys .
Location: co.dublin
Contact:

Re: Help Needed!!

Post by minionly »

Drop links???
User avatar
purplehaze
NON Member
Posts: 990
Joined: Wed Mar 30, 2011 2:42 pm
Whats your location?: Tallaght :p
Region: Southern
What Minis have you?: 1980 clubman b16 vtec
1992 mini shell, getting turbo,d
1974 clubman estate
Modifications: original-ish pffffft ye rite
Contact:

Re: Help Needed!!

Post by purplehaze »

Minis don't Hav drop links... haha. Honda on d mind haha
If it's bigger than a mini it's not a mini
User avatar
woody
IMOC Paid Member
Posts: 2823
Joined: Mon Feb 07, 2005 11:55 pm
Whats your location?: Drogheda
Region: Eastern
What Minis have you?: Traveller
Turbo
Hornet
Equinox
MINI Clubman
Location: LOUTH
Contact:

Re: Help Needed!!

Post by woody »

wheel bearing, balljoints, trackrod end , tiebar rubbers. Take the wheel off and look.
TECHNICAL MODERATOR
User avatar
macker
NON Member
Posts: 1950
Joined: Mon May 23, 2005 5:30 am
Whats your location?: THE FRIDGE
Region: Aboard
What Minis have you?: 110bhp 1968 mkII
Modifications: NEW Custom flakey paint
Location: The Fridge I told ye!!
Contact:

Re: Help Needed!!

Post by macker »

the bang could be caused by worn engine steadies and the exhaust,
if the steadies are worn when you slow down the engine rocks and lifts the back of the exhaust manifold hitting it off the underside of the car which might be your bang
ImageImageImage
mini mad sam
NON Member
Posts: 84
Joined: Sun Feb 06, 2011 10:29 pm
Whats your location?: midleton, county cork.
Region: Southern
What Minis have you?: 1985 MINI
1991 MINI
1975 MINI CLUBMAN ESTATE
Contact:

Re: Help Needed!!

Post by mini mad sam »

found wat was wrong!!
lower tie rod broke where it attaches to the subframe.
User avatar
Billy
IMOC Paid Member
Posts: 4649
Joined: Mon May 09, 2005 12:49 pm
Whats your location?: Roscommon
Region: Western
What Minis have you?: 1967 Morris Cooper, 1967 Austin Mini auto, 1968 Wolseley Hornet x2, 1981 Clubman Estate
Location: Roscommon
Contact:

Re: Help Needed!!

Post by Billy »

Is the subframe damaged, Sam? I have tie rods and a subframe if you're stuck.

Billy
mini mad sam
NON Member
Posts: 84
Joined: Sun Feb 06, 2011 10:29 pm
Whats your location?: midleton, county cork.
Region: Southern
What Minis have you?: 1985 MINI
1991 MINI
1975 MINI CLUBMAN ESTATE
Contact:

Re: Help Needed!!

Post by mini mad sam »

hi billy,
it broke where it bolts on to the subframe, just wondering could i weld a new bracket on to the subframe to take the tie rod end?
User avatar
macker
NON Member
Posts: 1950
Joined: Mon May 23, 2005 5:30 am
Whats your location?: THE FRIDGE
Region: Aboard
What Minis have you?: 110bhp 1968 mkII
Modifications: NEW Custom flakey paint
Location: The Fridge I told ye!!
Contact:

Re: Help Needed!!

Post by macker »

short answer, yes

It is the "L" bracket one that's on the front of the subframe on the drivers side isn't it?
ImageImageImage
User avatar
woody
IMOC Paid Member
Posts: 2823
Joined: Mon Feb 07, 2005 11:55 pm
Whats your location?: Drogheda
Region: Eastern
What Minis have you?: Traveller
Turbo
Hornet
Equinox
MINI Clubman
Location: LOUTH
Contact:

Re: Help Needed!!

Post by woody »

Can you post a picture? Have never seen the subframe break there before, what condition are the rubbers in?
TECHNICAL MODERATOR
Post Reply

Who is online

Users browsing this forum: No registered users and 0 guests