Welcome to the Irish Mini Owners Club Forum. Keep an eye out of on coming events!!!!

Jules

This section is for Mini projects and restorations and also the place to show off your pride and joy.

Moderators: spud1979, The Marcos Graveyard, Moderators

Post Reply
Ciotog
NON Member
Posts: 58
Joined: Sat Dec 31, 2011 11:04 pm
Whats your location?: Monaghan
Region: Northern
Contact:

Jules

Post by Ciotog »

Here she is. Just one pic at the minute cause it's dull in the garage. I'm going for the classic Red, White roof and stripes look. Should be painting in the next few weeks.

Image


D.M.G.T
NON Member
Posts: 703
Joined: Fri Dec 05, 2008 1:07 am
Whats your location?: Lismoy
Newtownforbes
Region: Western
Location: Longford
Contact:

Re: Jules

Post by D.M.G.T »

me thinks thats the project i sold few weeks ago..it a 88 mayfair? best of luck with it..
Image
Ciotog
NON Member
Posts: 58
Joined: Sat Dec 31, 2011 11:04 pm
Whats your location?: Monaghan
Region: Northern
Contact:

Re: Jules

Post by Ciotog »

Yeah she's an 88. I bought it from Skelly two weeks ago. Do you know much about it??
D.M.G.T
NON Member
Posts: 703
Joined: Fri Dec 05, 2008 1:07 am
Whats your location?: Lismoy
Newtownforbes
Region: Western
Location: Longford
Contact:

Re: Jules

Post by D.M.G.T »

Yea that's the one..I striped it all.it's been around the club two.know of two in the club that had it before me..needed some work..patch welded in floor ?
Image
Ciotog
NON Member
Posts: 58
Joined: Sat Dec 31, 2011 11:04 pm
Whats your location?: Monaghan
Region: Northern
Contact:

Re: Jules

Post by Ciotog »

Yeah its had a patch in the drivers footwell. She needs a patch under the rear seat and another in the passenger footwell. She's had sills replaced at one time. She has had a bang at the front before too, took an hour of wire brushing to remove the isapon which was a good 1/2 inch thick to uncover the ding. tapped it straight(ish) with a hammer and tried it up with a bit of filler, saves fitting a new front end. When all is said and done though it's good solid original shell. Going shopping tomorrow for doors, bonnet and boot lid.
D.M.G.T
NON Member
Posts: 703
Joined: Fri Dec 05, 2008 1:07 am
Whats your location?: Lismoy
Newtownforbes
Region: Western
Location: Longford
Contact:

Re: Jules

Post by D.M.G.T »

Yea from what I member the patchs on the floor where done brutal..and it wasn't me..they wer done with stick welder I'd say..
Image
Ciotog
NON Member
Posts: 58
Joined: Sat Dec 31, 2011 11:04 pm
Whats your location?: Monaghan
Region: Northern
Contact:

Re: Jules

Post by Ciotog »

Yeah there's a patch in the drivers side thats as rough as a bears arse. Think I might clean it up and plate it right.
Ciotog
NON Member
Posts: 58
Joined: Sat Dec 31, 2011 11:04 pm
Whats your location?: Monaghan
Region: Northern
Contact:

Re: Jules

Post by Ciotog »

Here's the lady that's gonna sacrifice her bits and pieces to help Jules on her way :)

Image

Image

So I now have

Front and Rear Subframes complete

2 Doors

Boot and Bonnet

99H997P Engine

Set of 10" minilites

Plus Brakes,Drives, suspension etc etc. :D
Ciotog
NON Member
Posts: 58
Joined: Sat Dec 31, 2011 11:04 pm
Whats your location?: Monaghan
Region: Northern
Contact:

Re: Jules

Post by Ciotog »

After spending a few hours at it today I got the engine running. After laying up for the last 10 years she running as sweet as a nut :D

Gonna drop it out this week clean it up and paint it.
guyfos
NON Member
Posts: 85
Joined: Thu Aug 07, 2008 5:52 pm
Contact:

Re: Jules

Post by guyfos »

That was my car for a few months!

If the engine your putting into it is the original one it hasnt been lying up for 10 years. More like 10 months.
Ciotog
NON Member
Posts: 58
Joined: Sat Dec 31, 2011 11:04 pm
Whats your location?: Monaghan
Region: Northern
Contact:

Re: Jules

Post by Ciotog »

No it's out of another mini. Didn't get an engine with the car.
Post Reply

Who is online

Users browsing this forum: No registered users and 1 guest