Welcome to the Irish Mini Owners Club Forum. Keep an eye out of on coming events!!!!
wheel nut size? (and tyre choice)
Moderators: spud1979, The Marcos Graveyard, Moderators
wheel nut size? (and tyre choice)
Hi all,
i have a 95 ex-Japan Mini, which unfortunately just picked up a puncture, first one since we got the car. It is fitted with minilites, and 145/70 R12 Yokohamas on the front, can't remember the rear tyre make, but they're a recognised brand which i got the seller to fit before purchase.
I noticed the puncture outside the house and went to change the tyre...(it was a scissor jack supplied with the car, ideally it should be the stand-type jack but thats another matter, and a 4 way wheel brace)
So i tried the wheel brace, fitted with a 17mm, 19mm, 21mm & i think 23mm. The 17 didnt fit, and the 19 felt like it was going to ring the nut on the wheel. As it happened, my neighbour was on the road and we got talking. He could see what was going on, and said he'd have a root in his shed. In the meantime i had tried the wheelbrace from my old Merc (no dice). My neighbour had another old-stlye wheel brace and this seemed to do the trick, although again it wasn't a perfect fit. Anyways, i got the offending flat off, and the spare on.
I had a look at the flat and noticed cracks in the tyre, apart from the dirty big screw which caused the puncture in the first place. So i'm thinking i'll get a pair of new tyres for the front, and thought i'd see if you guys would recommend a supplier such as camskills or eiretyres.
Has anyone had similar issues with wheel nuts? (is this more prevalent among ex-Japan cars?)
cheers
i have a 95 ex-Japan Mini, which unfortunately just picked up a puncture, first one since we got the car. It is fitted with minilites, and 145/70 R12 Yokohamas on the front, can't remember the rear tyre make, but they're a recognised brand which i got the seller to fit before purchase.
I noticed the puncture outside the house and went to change the tyre...(it was a scissor jack supplied with the car, ideally it should be the stand-type jack but thats another matter, and a 4 way wheel brace)
So i tried the wheel brace, fitted with a 17mm, 19mm, 21mm & i think 23mm. The 17 didnt fit, and the 19 felt like it was going to ring the nut on the wheel. As it happened, my neighbour was on the road and we got talking. He could see what was going on, and said he'd have a root in his shed. In the meantime i had tried the wheelbrace from my old Merc (no dice). My neighbour had another old-stlye wheel brace and this seemed to do the trick, although again it wasn't a perfect fit. Anyways, i got the offending flat off, and the spare on.
I had a look at the flat and noticed cracks in the tyre, apart from the dirty big screw which caused the puncture in the first place. So i'm thinking i'll get a pair of new tyres for the front, and thought i'd see if you guys would recommend a supplier such as camskills or eiretyres.
Has anyone had similar issues with wheel nuts? (is this more prevalent among ex-Japan cars?)
cheers
- Kenneth Murphy
- NON Member
- Posts: 1515
- Joined: Mon Sep 14, 2009 8:34 pm
- Whats your location?: knockbine
tullycanna
ballymitty
co. wexford. - Region: Eastern
- What Minis have you?: 1972 pick up
1979 leyland
88 designer - Location: south east region
- Contact:
Re: wheel nut size? (and tyre choice)
i had this with my old wheel nuts, they were old sizes. i used an 18 socket. when i replaced my wheels they were supplied with new shiny 19's
Re: wheel nut size? (and tyre choice)
Thanks Kenneth - can you just pick up 19mil wheel nuts in a motor factors?
Funny thing is, after feeling the wheel brace slip on the nut, i tried my socket set - lo and behold no 18mil socket ??
Funny thing is, after feeling the wheel brace slip on the nut, i tried my socket set - lo and behold no 18mil socket ??
Re: wheel nut size? (and tyre choice)
I imagine its an 11/16 old imperial your after
Slightly bigger than a 17mm yet smaller then an 18mm
Slightly bigger than a 17mm yet smaller then an 18mm
Jonesy
Re: wheel nut size? (and tyre choice)
thanks Jonesy - i thought it might be the old imperial size i'd be needing.
cheers
cheers
-
- IMOC Paid Member
- Posts: 2680
- Joined: Thu Feb 10, 2005 9:44 pm
- Whats your location?: Between an A series and a G13B
- Region: Eastern
- What Minis have you?: 61 van,68 MKII,
75 Clubman estate,
80 1275GT
91 RSP Cooper - Location: Between an A series and a G13B
- Contact:
Re: wheel nut size? (and tyre choice)
Yep 11/16 is what your after and if you can get a 6 sided socket instead of a mutipoint one all the better.Once you ring the stainless steel cap it is very difficult to get the nut loose.I find once you have damaged the nut the best method is to hammer the 11/16 socket over the nut and this all allow you to loosen to nut and replace with new nuts and always keep the 11/16 socket and breaker bar in the car and never let a tyre fitter near them.
Real Clubmans have a square nose.Seriously.
-
- NON Member
- Posts: 1278
- Joined: Sun Feb 06, 2005 10:41 pm
- Whats your location?: SOUTH EASTERN REGION
- Region: Eastern
- What Minis have you?: 1988 Mini Mayfair 998, 1971 Mini 1000, 2001 Transit Recovery Truck, 2001 fiat ducato camper, 2008 Kia cee’d, 1996 VW transporter T4, 1995 ford escort cabriolet.
- Location: Courtown. Wexford.
- Contact:
Re: wheel nut size? (and tyre choice)
Or if you pop the tin cover off the nut the 17 will fit.... just use a screw driver to get it off.
-
- IMOC Paid Member
- Posts: 2680
- Joined: Thu Feb 10, 2005 9:44 pm
- Whats your location?: Between an A series and a G13B
- Region: Eastern
- What Minis have you?: 61 van,68 MKII,
75 Clubman estate,
80 1275GT
91 RSP Cooper - Location: Between an A series and a G13B
- Contact:
Re: wheel nut size? (and tyre choice)
Ah but they look so much nicer with the caps on.
Real Clubmans have a square nose.Seriously.
Re: wheel nut size? (and tyre choice)
Yea im for the shiny caps left in tact too
Buy a Power-bar and 11/16 socket and your sorted
Buy a Power-bar and 11/16 socket and your sorted
Jonesy
- keith
- NON Member
- Posts: 2117
- Joined: Tue Jul 18, 2006 11:15 pm
- Whats your location?: Dún Laoghaire, Dublin
- Region: Eastern
- What Minis have you?: '93 SPi cooper
- Location: Dún Laoghaire, Dublin
- Contact:
Re: wheel nut size? (and tyre choice)
a quick check of both the websites you mentioned above shows CAMSKILL offering Falkens at 63.90 for two, post packing and tax included, delivered to Dublin . Eiretyres have a similar price, a few euro more, *but* are misleading in their advertising by adding a surcharge of €10 to the advertised price if you only buy one tyre.
my local tyre man quoted €10 a wheel for fitting and balancing. i think he includes air too. Don't laugh, air costs 50p a puff in UK...
my local tyre man quoted €10 a wheel for fitting and balancing. i think he includes air too. Don't laugh, air costs 50p a puff in UK...
- The Marcos Graveyard
- IMOC Paid Member
- Posts: 4720
- Joined: Fri Feb 04, 2005 10:05 am
- Whats your location?: Longford
- Region: Eastern
- What Minis have you?: 1971 Mini Marcos.
1984 Mini Sprite - Modifications: 1380cc
Weber45
S/C CR gearbox and drop gears - Location: Longford
- Contact:
Re: wheel nut size? (and tyre choice)
How big is a puff ?
-
- NON Member
- Posts: 1278
- Joined: Sun Feb 06, 2005 10:41 pm
- Whats your location?: SOUTH EASTERN REGION
- Region: Eastern
- What Minis have you?: 1988 Mini Mayfair 998, 1971 Mini 1000, 2001 Transit Recovery Truck, 2001 fiat ducato camper, 2008 Kia cee’d, 1996 VW transporter T4, 1995 ford escort cabriolet.
- Location: Courtown. Wexford.
- Contact:
Re: wheel nut size? (and tyre choice)
kerryminigringo wrote:Ah but they look so much nicer with the caps on.
I only mean while changing the wheel then pop them back on.......
Re: wheel nut size? (and tyre choice)
just an update folks - just off the phone to Sandyford Tyre Centre. I asked would they fit tyres if i supplied them myself. I was thinking of 4no Falken from Camskills, approx €30 a corner, plus shipping, plus €15 each for fitting. Works out at a shade over €200 all in. They matched the price, actually a few euro cheaper, so thats done and dusted - i'll get them fitted next week.
I'll have a look in the local motor factors during lunch for a 11/16 spanner.
I'll have a look in the local motor factors during lunch for a 11/16 spanner.
- The Marcos Graveyard
- IMOC Paid Member
- Posts: 4720
- Joined: Fri Feb 04, 2005 10:05 am
- Whats your location?: Longford
- Region: Eastern
- What Minis have you?: 1971 Mini Marcos.
1984 Mini Sprite - Modifications: 1380cc
Weber45
S/C CR gearbox and drop gears - Location: Longford
- Contact:
Re: wheel nut size? (and tyre choice)
Spanner is no good, get a socket.
Re: wheel nut size? (and tyre choice)
^ my bad, i did mean a socket.
Who is online
Users browsing this forum: No registered users and 0 guests